LILO
Sean
picasso@madflower.com
Sat, 29 Apr 2000 17:19:15 -0400 (EDT)
Personally, I think your running into the >1024 cylinder boot
partition problem. I believe this is covered in the LILO How-To, but i
believe you are going to have to move your /boot partition onto a cylinder
<1024 with in your case would require moving some files around.
The <1024 boot problem is a BIOS limitation.
On Sat, 29 Apr 2000, Marcel Kunath wrote:
> Oh boy. I was wondering how good this new prog works.
>
> I don't use Windows anymore so I am not sure. I read the QuickInst file and
> there at some point it says: Use this LILO only on a fresh install and not as
> update. But still it shouldn't choke.
>
> I just saw one thing in you lilo.conf I never use(d).
>
> root=current
>
> I always define what partition the kernel is in.
>
> Here the lilo of a dual boot machine in Sydney.
>
> boot=/dev/hda
> #compact # faster, but won't work on all systems.
> vga = normal # force sane state
> read-only
> prompt
> timeout=250
> # End LILO global Section
> #
> image = /vmlinuz
> root = /dev/hdb1
> label = linux
>
> #
> image = /boot/vmlinuz
> root = /dev/hdb1
> label = linux.old
>
> #
> other = /dev/hda1
> label = win
> table = /dev/hda
>
> The thing has two harddrives.
>
> mk
>
> > Thanks. Sorry I left
> off the /etc/lilo.conf
> file. Here you go: > > [root@spitzcor spitzcor]# cat /etc/lilo.conf
> > # LILO configuration created by QuickInst 21 Sat Apr 29 14:50:58 EDT
> > 2000
> >
> > boot = /dev/hda
> > compact
> > delay = 5 # optional, for systems that boot very quickly
> > vga = normal # force sane state
> > root = current # use "current" root
> > image = /boot/vmlinuz
> > label = linux
> > other = /dev/hda1
> > table = /dev/hda
> > label = win95
> >
> > And I've already run /sbin/lilo manually, same problem.
> >
> > Thanks a lot,
> > -Cory
> >
> > Alan Garrison wrote:
> > >
> > > Cory Spitz wrote:
> > > >
> > > > Hello all,
> > > >
> > > > I'm a linux newbie and just got myself setup with Linux-Mandrake 7.0. I
> > > > can only boot the system from a floppy becuause I can't seem to get LILO
> > > > installed properly.
> > >
> > > Just a few thoughts, not presented in any particular order:
> > > 1. You might want to post the contents of your /etc/lilo.conf file.
> > > 2. Try running the /sbin/lilo command manually after checking
> > > the above config file.
> > > 3. Even if you can't get LILO working, you may be able to still
> > > boot Linux via LOADLIN.
> > > 4. Check out the hdparam command (see man page) for more hard drive
> > > info.
> >
> > _______________________________________________
> > linux-user mailing list
> > linux-user@egr.msu.edu
> > http://www.egr.msu.edu/mailman/listinfo/linux-user
> >
>
>
> --
> Marcel Kunath
>
> *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
>
> Montie House Network Greater Lansing Linux Users Group
> http://www.montiehouse.com http://www.gllug.org
>
> *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
>
> _______________________________________________
> linux-user mailing list
> linux-user@egr.msu.edu
> http://www.egr.msu.edu/mailman/listinfo/linux-user
>